HSX
59 / 65 / 71 Extra Large Swing Lathes

Standard Features

  • 40 HP, 4P Main Motor
  • 6” Spindle Bore (Opt. 9 – 16”)
  • Spindle Nose: ASA-A2-15 (Opt. A2-20)
  • Rear Chuck Adapter
  • 4 Jaw 50” Face Plate
  • 23.6” Steady Rest with Roller Jaw (Min. Capacity11”)
  • Set of Change Gears for Special Leads
  • Hardened and Ground Bedways
  • Tool Slide with T-Slot
  • Thread Chasing Dial
  • 4-Way Rapid Traverse
  • Hydraulic Brake System
  • Full Length Splashguard
  • Self-Spacing Supports For Lead Screw, Feed Rod & Control Rod
  • Coolant System with Pump and Piping
  • Tailstock Safety Locking Chock
  • 2-Speed Drive Tailstock Quill
  • Pull Drawer Chip (Coolant) Pan
  • Tool Box with Necessary Wrenches & Spanners
  • UL Electrical parts
  • Instruction Manual and Parts List

Optional Accessories

  • 11.8” Steady Rest With Roller Jaws (Min. Capacity 2.78”)
  • 31.5” Steady Rest With Roller Jaws
  • Follow Rest (Pad Jaw)
  • Roller Bracket (Two point)
  • Halogen Work Light
  • 70.8” Face Plate and Boring Mill Jaws (4 pcs independent)
  • Motorized Tailstock Body
  • 55” Chuck Guard
  • Traveling Chip Guard (Follows the carriage)
  • Tool post Small Splash guard
  • Longitudinal Feed Stop
  • Digital Readout (DRO)
  • Aloris Tool Post & Sets
  • 3-Jaw and 4-Jaw Manual Chucks
Capacity HSX-59 HSX-65 HSX-71
Swing Over Bed 59" 65" 71"
Swing Over Cross Slide 47" 53" 59"
Swing in Gap 80" 86" 92"
Width of Bed 33" 33" 33"
Distance Between Centers 80” – 472” 80” – 472” 80” – 472”

 

Headstock HSX-59 HSX-65 HSX-71
Spindle Bore 6” – 16” 6” – 16” 6” – 16”
Type of Spindle Nose A2-15 - A2-20 A2-15 - A2-20 A2-15 - A2-20
Number of Spindle Speeds 12 12 12
Spindle Speed 4 – 400 RPM (6”, 12”, 14”, 16”)
5 – 500 RPM (9”, 10”)
4 – 400 RPM (6”, 12”, 14”, 16”)
5 – 500 RPM (9”, 10”)
4 – 400 RPM (6”, 12”, 14”, 16”)
5 – 500 RPM (9”, 10”)

 

Gear Box HSX-59 HSX-65 HSX-71
Number of Feed Changes 60 Kinds 60 Kinds 60 Kinds
Longitudinal Cross 0.003” – 0.198in/rev (0.0017-0.099in/rev) 0.003” – 0.198in/rev (0.0017-0.099in/rev) 0.003” – 0.198in/rev (0.0017-0.099in/rev)
Leadscrew Diam. & Threads per Inch 2 1/4” & 2 TPI 2 1/4” & 2 TPI 2 1/4” & 2 TPI
Threading range - Whitworth ½ - 30 TPI (60 kinds) ½ - 30 TPI (60 kinds) ½ - 30 TPI (60 kinds)
Threading range - Metric 1 to 60mm pitch (52 kinds) 1 to 60mm pitch (52 kinds) 1 to 60mm pitch (52 kinds)
Threading range - Module 0.25 - 15 (43 kinds) 0.25 - 15 (43 kinds) 0.25 - 15 (43 kinds)
Threading range - D.P. 2 - 120 D.P. (60 kinds) 2 - 120 D.P. (60 kinds) 2 - 120 D.P. (60 kinds)

 

 

Tool Slide HSX-59 HSX-65 HSX-71
Maximum Travel of Compound 16.5” 16.5” 16.5"
Maximum Travel of Cross Slide 38” 38” 38”

 

 

Tailstock HSX-59 HSX-65 HSX-71
Tailstock Quill Travel 11.8” 11.8” 11.8”
Tailstock Quill Diameter 7.08” 7.08” 7.08”
Tailstock Center M.T. #6 (Opt. M.T. #7) M.T. #6 (Opt. M.T. #7) M.T. #6 (Opt. M.T. #7)

 

Motor HSX-59 HSX-65 HSX-71
Main Drive Motor 40 HP*4P  40 HP*4P  40 HP*4P 
Coolant Pump Motor 1/4 HP 1/4 HP 1/4 HP

 

Dimensions HSX-59 HSX-65 HSX-71
Floor Space  89”W X 92”H               161” – 555” 161” – 555” 161” – 555”
Weight (lbs) 24,691 – 57,761 lbs 24,691 – 57,761 lbs 24,691 – 57,761 lbs